830-01 Exam Questions

In order to reset the admin password that has been lost, the procedure can be done via what type of connection to a Steelhead appliance?

What is the command to return a Steelhead appliance back to factory defaults?

What is the command to clear all statistics on a Steelhead appliance?

What is the CLI command for starting the Configuration Wizard?

What steps take place during an upgrade process?

Which command shows the last boot partition and the next boot partition? (Select 2)

You are configuring HighSpeed TCP in an environment with an OC-3 (155Mb/s) and 60 milliseconds of round-trip latency. You know that the rule of thumb is to set the Steelhead applia...

You are configuring HighSpeed TCP in an environment with an OC-3 (155Mb/s) and 60 milliseconds of round-trip latency. You know that the rule of thumb is to set the WAN router queue...

When using Correct Addressing, what is the out-of-band (OOB) splice connection described as?

In a Steelhead appliance deployment, the customer decides to use Full Transparency and block all incoming/outgoing TCP connections on port 7800 on their firewall. However, they are...

A single client-server TCP connection is made through two Steelhead appliances (default in-path deployment). This is a lab-controlled environment and no other client-server connect...

Which of the following commands followed by "write memory" will allow you to turn off in-path optimization but turn it back on upon rebooting the Steelhead appliance?

What port number is should be configured on a Steelhead appliance to communicate to the AAA RADIUS server?

When using Correct Addressing, without Enhanced Auto-discovery (EAD), what is the size of the probe response in the return SYN/ACK packet from the server-side Steelhead appliance?

What is contained in the probe of the return SYN/ACK packet when using enhanced auto-discovery (EAD)?

What probe is being used in the inner channel between two Steelhead appliances when using Full Transparency in hex?

Connection pooling feature on RIOS pre-establishes:

When upgrading from Steelhead EX v1.0 to Steelhead EX v2.0, what happens to existing VM slots on the appliance?

During an upgrade, what steps are necessary to convert VM slots for use in Steelhead EX v2.0? (Select 3)

VSP on the Steelhead EX supports which features of VMware virtual machines? (Select 3)

What differences are there between upgrading an active VSP configuration from Steelhead EX v1.0 to Steelhead vEX 2.0 and installing a fresh Steelhead EX v2.0 appliance? (Select 2)

RIOS v7.0 and later, the packet-mode-optimization feature can: (Select 2)

RIOS v7.0 and later the Steelhead Appliance can use HTTP stream splitting to optimize two different live video technologies: (Select 2)

The adaptive data streamlining provides you:

On an Interceptor appliance running Fair Peering v2, what Steelhead characteristic is used to calculate peer affinity?

In the Interceptor appliance version 3.0 and later the command to enable cluster failover is:

On the Interceptor appliance, the Networking > Steelheads page displays which of the following?

When deploying Interceptor appliances on aggregated links, you must: (Select 2)

When deploying failover Interceptors, all in-path interfaces must:

When deploying Interceptor appliances in a parallel cluster what feature must be disabled to ensure packet redirection upon failure?

What action is taken by the Interceptor if a connection does not match a configured load balance rule and the default pool is empty?

How do you clear the peer affinity information from an Interceptor?

The fair peering feature on Interceptor appliances can be enabled:

The Xbridge feature on Interceptor provides:

Refer to the exhibit. The connection from USER1, going to SERVER2 is not being optimized by SH10. What is the possible cause? (Select 2)

-- Exhibit -- Refer to the exhibit. In a WCCP environment with R3, SH10 and SH11, the following screenshot shows that the load is not being distributed evenly in between the Steelh...

-- Exhibit -- Refer to the exhibit. In a WCCP environment with R3, SH10 and SH11, it was observed that the returning traffic from Server2 is not being optimized by the Steelhead ap...

-- Exhibit -- Refer to the exhibit. In a WCCP environment with R3, SH10 and SH11, according to the exhibit attached, which statements are true? (Select 2)

-- Exhibit -- Refer to the exhibit. In a WCCP environment with R3, SH10 and SH11, which statement below is true?

-- Exhibit -- Refer to the exhibit. A Steelhead administrator has recently decided to configure data store synchronization between 2 Steelhead appliances on his data center. After...

Refer to the exhibit. The connections from USER1 to Server3 are not being optimized. What is the possible cause? (Select 2)

Refer to the exhibit. A Steelhead administrator has recently decided to implement two Interceptor appliances and one Steelhead appliance on his data center. After configuring the I...

Refer to the exhibit. A Steelhead administrator has recently decided to implement two Interceptor appliances and one Steelhead appliance on his data center. After configuring the I...

Refer to the exhibit. A Steelhead administrator has decided to implement two Interceptor appliances and one Steelhead appliance on his data center. After configuring the Intercepto...

Refer to the exhibit. A Steelhead administrator has recently decided to implement two Interceptor appliances and one Steelhead appliance on his data center. After configuring the I...

Refer to the exhibit. According to the information shown, what statements are true? (Select 2)

Refer to the exhibit. According to the log information, what does that message represent? (Select 2)

Refer to the exhibit. According to the packet capture, what statements are true? (Select 2)

A Steelhead administrator has recently decided to troubleshoot a TCP connection. He wants to find out if the Steelhead is adding a probe into the TCP SYN packets. For some reason,...

Refer to the exhibit. What does the display represent? (Select 2)