830-01 Exam Questions
385 real 830-01 exam questions with expert-verified answers and explanations. Page 5 of 8.
- Question #201
Assuming auto-discovery is used, WCCP redirect-in statements would normally be placed on which router interfaces? (Select 2)
- Question #202
When deploying policy-based routing for multiple Steelhead appliances in a cluster, the router should be configured to: (Select 2)
- Question #203
When bi-directional network address translation (NAT) is used between the Steelhead appliances, optimization is not working. A workaround to this is: (Select 2)
- Question #204
Simplified routing learns to associate MAC addresses to IP addresses by: (Select 2)
- Question #205
When would Simplified Routing Destination Only be used? (Select 2)
- Question #206
When enabling MS-SQL Layer 7 optimizations, what are the best practices to use? (Select 2)
- Question #207
What is the default Connection Forwarding keep alive interval?
- Question #208
When Connection Forwarding is in use, when a neighbor fails, the default behavior of the remaining neighbor will be to:
- Question #209
In an implementation using a 4-port card, which interface could be used as the Connection Forwarding neighbor? (Select 2)
- Question #210
In configuring failover settings, which of the following ports is set as the default for communicating with the backup Steelhead appliance?
- Question #211
In configuring failover settings, which of the following interfaces is used for communicating with the backup Steelhead appliance?
- Question #212
Which of the following interfaces should be used for datastore synchronization? (Select 2)
- Question #213
What is the supported redirection scheme/s used when a Steelhead appliance is in a WCCP deployment?
- Question #214
When enabling WCCP v2 support, what does a multicast TTL value of 1 imply?
- Question #215
Which of the following control messages are NOT used by WCCP? (Select 2)
- Question #216
Which of the following points on WCCP v2 are correct? (Select 4)
- Question #217
Assume that a packet being optimized by SH10 incorrectly ends up on SH11 (due to load balancing error, or similar). How can you ensure that this packet is correctly returned to SH1...
- Question #218
In the exhibit, where should the WCCP redirection take place for traffic originating from the clients to the servers, assuming redirect IN is used?
- Question #219
In the exhibit, where should the WCCP redirection take place for server return traffic, assuming redirect IN is used? (Select 2)
- Question #220
which interfaces should the WCCP router R1 listen to for multicast communication with the server-side Steelhead appliances, assuming the multicast address is 239.0.0.0.1? (Select 2...
- Question #221
The customer would like to prevent a "black-holing" situation when using PBR when SH11 goes down. What options are available to determine state-level status of the Steelhead applia...
- Question #222
How can you enable SkipWare?
- Question #223
Select the command needed to add support for virtual in-path to your Steelhead appliance so that you can use WCCP or PBR with a Steelhead appliance.
- Question #224
To prevent possible denial of service attack, such as TCP SYN flooding, which of the following features could be used?
- Question #225
When two or more Steelhead appliances are configured with Connection Forwarding in such environments as WCCP clustering, what feature will allow remaining Steelhead appliances to c...
- Question #226
A customer wants to optimize traffic from remote VPN sites to DMZ servers in the data center shown in the accompanying exhibit. The current network architecture can satisfy these r...
- Question #227
Hybrid Mode can best be defined as a combination of:
- Question #228
The Primary interface is REQUIRED for which deployment methods and features? 1) In-path 2) Server-side out-of-path 3) Logical in-path (WCCP/PBR) 4) Hybrid Mode 5) Proxy File Servic...
- Question #229
Which of the following IP addressable interfaces can be connected for management purposes? 1) WAN 2) LAN 3) Primary 4) AUX 5) In-path
- Question #230
The IP address for which neighbor interface should be configured for Connection Forwarding? 1) lan0_0 2) inpath0_0 3) Primary 4) AUX 5) inpath7_7
- Question #231
In order to achieve optimization using auto-discovery for traffic coming from site C and destined to site A in the exhibit, which configuration below would be required?
- Question #232
Which of the following methods can be used to reduce the load on a router configured to use outbound interface WCCP redirection? (Select 3)
- Question #233
Which of the following statements are true about server-side out-of-path deployments? (Select 4)
- Question #234
A server-side logical in-path deployment is shown in the exhibit. Additionally, SH12 is configured with a fixed-target rule pointing to SH11. The client behind SH12 will not be abl...
- Question #235
In the exhibit, there is a resident firewall inside the WAN cloud that drops packets with any TCP option. The customer allows you to use fixed-target rules instead. The firewall po...
- Question #236
In a WCCP configuration, during a packet trace, you notice the return WCCP communication on a CAT 6500 is using GRE. The Steelhead appliance is directly connected to it. What can b...
- Question #237
What CLI command is used to view logs?
- Question #238
In a previously optimized environment, users have recently upgraded their Windows XP workstations to Windows 7. After the upgrade, users are complaining about slow CIFS and encrypt...
- Question #239
What is the command to view configuration files on the CLI?
- Question #240
Which of the following authentication methods are supported by the Steelhead appliance?
- Question #241
What is the default authorization policy used by Steelhead appliances?
- Question #242
What port number is configured on a Steelhead appliance to communicate to the TACACS+ server?
- Question #243
Which of the following custom TACACS+ attribute-value (AV) pairs gives the user guest privileges?
- Question #244
What is the default trap severity for system messages?
- Question #245
How do you view the full configuration in the CLI?
- Question #246
How do you clean the datastore on a Steelhead appliance? 1) > restart empty 2) > reload clean 3) # restart empty 4) # reload clean 5) (config) # reload clean
- Question #247
Place the following commands to upgrade a Steelhead appliance from the CLI in the correct order. (NotE. include only the necessary steps) 1) SH (config) image install image.img 2 3...
- Question #248
Which of the following commands will show the log level configuration? (Select 2)
- Question #249
Which command will display current alarm status information?
- Question #250
What is the process for dropping the connection of an individual user that is currently being optimized? As an example, consider an HTTP connection being optimized with a local add...