500-005 Exam Questions

From where does the LCU receive its instructions?

The configured speed-dial numbers are located in which section of the Cisco TelePresence Touch 12?

Which hard button on the Cisco TelePresence Touch 12 console is used to end an active call?

Which two options describe the functions of the TX9000 codec? (Choose two.)

After the TX9000 log files are captured, which file will contain the name of the problem type that was selected from the Select a Problem menu?

Refer to the exhibit. Which option is valid to test the LCU of the TX9000 system?

What is the build number for the following Cisco TelePresence System image? cmterm-CTS.1-9-1-68R-K9.P2.cop.sgn

Refer to the exhibit. Which option adjusts the white balance on the left screen?

Which Cisco Unified Communications Manager GUI is used to upload a new Cisco Option Package file before the TX9000 can be upgraded?

Refer to the exhibit. After the image name was specified for the TX9000 under the Cisco Unified Communications Manager Device Defaults screen, and the TX9000 was restarted, the TX9...

Refer to the exhibit. Which CLI was used to obtain this information?

In order to place a call to 5001 using the CLI, which command is correct?

After DHCP is enabled and a new TX9000 system is configured in Cisco Unified Communications Manager, the TX9000 displays an IP address of 192.168.100.2, which is not what was expec...

After the initial bootup of a TX9000 system, you notice that the software version on the codec is not what was expected. Which location should be searched to ensure that the desire...

In which situation would a new TX9000 system boot up as a Cisco TelePresence System 500-32 device?

Refer to the exhibit. Which option allows for reporting a problem from the TX9000 TelePresence Touch 12?

An end user has reported that the TX9000 TelePresence Touch 12 screen does not power down. Which option is the correct response?

The TX9000 fails to boot completely and is stuck on Step 5 of seven steps as displayed on the Cisco TelePresence Touch 12. Which step should be implemented to correct the problem?

If the TX9000 system is experiencing "phantom switching," what should be done to troubleshoot the problem?

When the TX9000 boots up, green progress check marks are displayed on the screen. After successful bootup, six check marks are displayed. Which of these can cause the fourth check...

When the TX9000 boots up, green progress check marks are displayed on the screen. After successful bootup, six check marks are displayed. Which of these can cause the last check ma...

Which TX9000 display choice is best for reducing possible issues with viewing angles for conference participants?

Which two factors are crucial to the immersive Cisco TelePresence experience? (Choose two.)

The control cable for the 42-inch Auto Collaboration display connects to which component?

Which of these determines the specific role for each codec?

When using the TX9000 AV expansion box, how many total video output signals can be obtained using a single video input?

Which device is connected to the TX9000 AV expansion box for video input?

Which three components does the LCU control? (Choose three.)

Which option allows the TX9000 to receive its configuration and software image from a TFTP server when a DHCP server is not available?

Refer to the exhibit. Under which configuration components is the TFTP server specified?

Refer to the exhibit. Under which component is the TX9000 configuration restored to factory configuration?

Which TX9000 codec will receive image files from the TFTP server?

If no speed-dial numbers are displayed on the Cisco TelePresence Touch 12 Favorites screen, which of these is the cause?

When fine-tuning the TX9000 displays for optimal performance, what is the primary factor in getting the optimal color temperature for the displays?

Which component is used to calibrate the TX9000 system microphones?

Which adjustment screw is used on the cameras of a TX9000 to fine-tune the yaw?

How can TX9000 log information be sent to a remote server?

Periodic capture of TX9000 logs is configured in which subsection of the TX9000 device configuration in Cisco Unified Communications Manager?

Which statement about the TX9000 codec is true?

When a new TX9000 system is being installed, where does the TX9000 obtain its system image?

The TX9000 should be configured in Cisco Unified Communications Manager as which type of endpoint?

When configuring the Device Information section of a new TX9000 in Cisco Unified Communications Manager, which two selections are required to be checked? (Choose two.)

Which three items must be configured for the TX9000 to automatically obtain the TFTP server? (Choose three.)

The TX9000 center speaker connects to which component?

The TX9000 left and right speakers connect to which component?

What is causing the Cisco TelePresence Touch 12 to show Project/LCD in error?

Which two options cause the presentation to not show on the Active Collaboration data display and show only in PiP on the TX9000 plasma screen? (Choose two.)

What is the function of the Presentation Devices test from the Cisco TelePresence Administration GUI?

When a laptop was connected to the TX9000 presentation codec and the Presentation icon was tapped on the Cisco TelePresence Touch 12, the presentation sharing failed. Which option...

What is the recommend latency needed in order to provide a user with a good Telepresence experience?