4A0-M01 Exam Questions
137 real 4A0-M01 exam questions with expert-verified answers and explanations. Page 1 of 3.
- Question #1
Click on the exhibit. The command result indicates which condition on the Inverse Multiplexing over ATM (IMA) bundle?
- Question #2
Which timing technique can deliver time of day and phase synchronization information to the base station without concern for Packet Delay Variation (PDV)?
- Question #3
When messages, periodically sent between an IEEE 1588v2/Precision Time Protocol (PTP) v2 master and slave, serve as hellos to help the slave choose the best available master?
- Question #4
Click on the exhibit. Consider the topology and MLS1 configuration shown, and given the following conditions: * MLS1 delivers the PRC traceable clock to the network * Reference 1 r...
- Question #5
Click on the exhibit. Given the show command results shown: Which IEEE 1588v2/Precision Time Protocol (PTP) v2 message did the slave node set the Unicast message rates used by the...
- Question #6
Which statement best describes adaptive timing techniques?
- Question #7
If an IEEE 1588v2/Precision Time Protocol (PTP) v2 slave times out announce messages with the master, to which state does the slave port transition to choose another potential mast...
- Question #8
Click on the exhibit. Given the configuration shown and the following conditions: * The external reference is offline * Reference 1 receives Quality Level (QL) - EEC1 * Reference 2...
- Question #9
Click on the exhibit. Given the show command results shown: Which IEEE 1588v2/Precision Time Protocol (PTP) v2 parent clock value does the slave first consider when choosing its ma...
- Question #10
An SROS router obtains its timing exclusively from its BITS input port. The router sets Quality Level (QL) SONET Traceability Unknown (STU) on this Superframe (SF) framed DS1 BITS...
- Question #11
Consider the topology and MLS1 configuration shown, and given the following conditions: * MLS1 delivers the PRC traceable clock to the network * Reference 1 receives Quality Level...
- Question #12
Which synchronization technique supports time of day and phase synchronization?
- Question #13
Which is a characteristic of the IEEE 802.3 Slow Protocol?
- Question #14
Which statement best describes phase synchronization as it is used in the backhaul transport?
- Question #15
Which command example correctly configures a 7750 Service Router (SR) for Synchronous Ethernet (SyncE) support?
- Question #16
Which component must you configure on an IEEE 1588v2/Precision Time Protocol (PTP) v2 slave to enable it to choose its master based on Synchronization Status Message (SSM) Option 1...
- Question #17
Consider the topology and MLS1 configuration shown, and given the following conditions: * MLS1 delivers the PRC traceable clock to the network * Reference 1 receives Quality Level...
- Question #18
Based on the default SROS Border Gateway Protocol (BGP) timer settings and the configuration shown: If the Interior Gateway Protocol (IGP) removes its route to the BGP neighbor 192...
- Question #19
Given the topology shown: With Border Gateway Protocol (BGP) peer tracking enabled, what will router MLS1 do if the Interior Gateway Protocol (IGP) removes its route to its BGP pee...
- Question #20
You wish to protect the LSP POC3-1, POC3-2 with a manual bypass tunnel. Which statement correctly describes the manual bypass tunnel configuration requirement for the ring topology...
- Question #21
Which field in the show command result indicates that the router MLS1 is configured as a Border Gateway Protocol (BGP) route reflector?
- Question #22
With the information given, why is the second static route to prefix 192.0.2.2/32 inactive?
- Question #23
You wish to configure a secondary static route on MLS1 targeting the CSA1 system interface. The route must forward packets over the secondary route path as shown in the diagram. Gi...
- Question #24
Which statement correctly describes a Versatile Service Module (VSM) Layer 2 and Layer 3 service cross-connect's operation?
- Question #25
Which statement correctly describes Virtual Routing and Redundancy Protocol (VRRP) configuration?
- Question #26
Choose the two SAP identifiers that a Cross Connect ID (CCID) can bind to create a bi-directional Layer 2 and Layer 3 service cross connect. (Choose two.)
- Question #27
Given the diagram shown and the following information: - Configured on the CSA1 router is an ePipe with redundant spoke Service Distribution Points (SDPs) - The spoke SDPs terminat...
- Question #28
Given the configurations shown and the following information: - Multilayer Switch (MLS) 1 and 2 host duplicate Virtual Private Routed Network (VPRN) services. - Configured on the i...
- Question #29
Given the diagram. Given the local Provider Edge (PE) router configuration shown and the following condition: - All Service Access Points (SAPs) and spoke SDPs are operational Upon...
- Question #30
A network element (NE) forwards external traffic through a Virtual Routing and Redundancy Protocol (VRRP) protected gateway interface. If the master goes offline, how does the NE l...
- Question #31
Which statement correctly describes SROS Virtual Private Wire Service (VPWS) endpoint characteristics?
- Question #32
Which statement correctly describes the IPE pipe service operation?
- Question #33
As cells enter an aPipe service configured for vc-type atm-vcc, how does the ingress Provider Edge (PE) router handle the cell header Virtual Path Identifier/Virtual Channel Identi...
- Question #34
Click on the exhibit Which statement correctly describes eNodeB-to-eNodeB X2 interface traffic flow in the Model 1 hub and spoke architecture Long Term Evolution (LTE) service mode...
- Question #35
Which statement correctly describes the Model 1 hub and spoke architecture Long Term Evolution (LTE) service model shown?
- Question #36
Click on the exhibit. Given the show command results shown and the following information: * MLS1 interface L3_VLAN402 is the preferred Virtual Router ID (VRID) 1 master interface *...
- Question #37
Which statement is correct concerning spoke SDP use in point-to-point services?
- Question #38
Click on the exhibit. Given the show command result shown and the following information: * The local Provider Edge (PE) IES 300 service uses redundant pseudowires spoke-terminated...
- Question #39
Which statement is true concerning aPipe ATM cell mode versus ATM Adaptation Layer (AAL) 5 Service Data Unit (SDU) frame mode?
- Question #40
Click on the exhibit. Given the show result shown: Which example shows the proper format for a Service Access Point (SAP) configured within this service context?
- Question #41
Click on the exhibit Given the diagram shown, and the following information: * Configured on CSA1 and the two MLS routers is redundant aPipe 300 * Interchassis Backup Pseudowires (...
- Question #42
Given the diagram and the following information: - Virtual Private Routed Network (VPRN) 5 spans the routers Point of Concentration (POC) 3-1 and 3-2 and the Multilabel Switch (MLS...
- Question #43
Which statement correctly describes the port configuration shown?
- Question #44
Given the configuration example shown: The DS1 port shown will become a Structure Agnostic TDM over Packet (SAToP) Service Access Point (SAP) access port. What must be configured o...
- Question #45
Given the configuration shown and the following information: - The port configured as shown is used in a cPipe Service Service Access Point (SAP) 1/2/1.1 - Each packet contains a 2...
- Question #46
Given the show results shown, and the following information: - CSA1 originates a redundant ePipe service - The remote PE Service Access Points (SAPs) are Multichassis-Link Aggregat...
- Question #47
Which statement correctly describes bi-directional Automatic Protection Switching (APS) as implemented in SROS?
- Question #48
Given the diagram shown, and the following information: - Configured on CSA1 is a redundant ePipe service - A Multichassis Link Aggregation Group (MC-LAG) protects the CE access li...
- Question #49
In the exhibit, how does the signaled pseudowire status affect the VPRN 5 service?
- Question #50
Given the show command and the result shown: ``` ArcSaz# show service id 300 base =============================================================================== Service Basic Info...