156-315.76 Exam Questions

In an R76 Cluster, some features such as VPN only function properly when:

In ClusterXL R76; when configuring a cluster synchronization network on a VLAN interface what is the supported configuration?

Which process is responsible for delta synchronization in ClusterXL?

Which process is responsible for full synchronization in ClusterXL?

Which process is responsible for kernel table information sharing across all cluster members?

By default, a standby Security Management Server is automatically synchronized by an active Security Management Server, when:

The ________ Check Point ClusterXL mode must synchronize the physical interface IP and MAC addresses on all clustered interfaces.

After you add new interfaces to a cluster, how can you check if the new interfaces and the associated virtual IP address are recognized by ClusterXL?

__________ is a proprietary Check Point protocol. It is the basis for Check Point ClusterXL inter- module communication.

Which of the following is a supported Sticky Decision Function of Sticky Connections for Load Sharing?

Included in the customer's network are some firewall systems with the Performance Pack in use. The customer wishes to use these firewall systems in a cluster (Load Sharing mode). H...

A connection is said to be Sticky when:

How does a cluster member take over the VIP after a failover event?

Check Point Clustering protocol, works on:

A customer is calling saying one member's status is Down. What will you check?

A customer calls saying that a Load Sharing cluster shows drops with the error First packet is not SYN. Complete the following sentence. I will recommend:

Which of the following commands can be used to troubleshoot ClusterXL sync issues?

John is configuring a new R76 Gateway cluster but he can not configure the cluster as Third Party IP Clustering because this option is not available in Gateway Cluster Properties....

Which of the following commands shows full synchronization status?

Which of the following commands shows full synchronization status?

In ClusterXL, _______ is defined by default as a critical device.

In ClusterXL, _______ is defined by default as a critical device.

Refer to Exhibit below: Match the ClusterXL modes with their configurations.

When synchronizing clusters, which of the following statements is NOT true?

When synchronizing clusters, which of the following statements is NOT true?

When a failed cluster member recovers, which of the following actions is NOT taken by the recovering member?

Organizations are sometimes faced with the need to locate cluster members in different geographic locations that are distant from each other. A typical example is replicated data c...

You are the MegaCorp Security Administrator. This company uses a firewall cluster, consisting of two cluster members. The cluster generally works well but one day you find that the...

You have a High Availability ClusterXL configuration. Machines are not synchronized. What happens to connections on failover?

What command will allow you to disable sync on a cluster firewall member?

When using ClusterXL in Load Sharing, what is the default method?

If ClusterXL Load Sharing is enabled with state synchronization enabled, what will happen if one member goes down?

In the following cluster configuration; if you reboot sglondon_1 which device will be active when sglondon_1 is back up and running? Why?

What is a "sticky" connection?

Your network includes ClusterXL running Multicast mode on two members, as shown in this topology: Your network is expanding, and you need to add new interfaces: 10.10.10.1/24 on Me...

Match the Best Management High Availability synchronization-status descriptions for your Security Management Server (SMS):

Review the R76 configuration. Is it correct for Management High Availability?

Check Point New Mode HA is a(n) _________ solution.

What is the behavior of ClusterXL in a High Availability environment?

Review the cphaprob state command output from one New Mode High Availability ClusterXL cluster member. Which member will be active after member 192.168.1.2 fails over and is reboot...

Review the cphaprob state command output from a New Mode High Availability cluster member. Which machine has the highest priority?

By default Check Point High Availability components send updates about their state every:

You have just upgraded your Load Sharing gateway cluster (both members) from NGX R65 to R76. cphaprob stat shows: Which of the following is not a possible cause of this?

In Management High Availability, what is an Active SMS?

For Management High Availability, if an Active SMS goes down, does the Standby SMS automatically take over?

For Management High Availability synchronization, what does the Advance status mean?

Which of the following would be a result of having more than one active Security Management Server in a Management High Availability (HA) configuration?

You want to verify that your Check Point cluster is working correctly. Which command line tool can you use?

How can you view the virtual cluster interfaces of a Cluster XL environment?

How can you view the critical devices on a cluster member in a Cluster XL environment?