NS0-506 Exam Questions

Given the information shown in the diagram, Which port has a NetApp device attached to it?

To implement Lossless Ethernet, which frame command do switch vendors execute to control flow?

An organization currently has a NetApp Fibre Channel, FCP block based solution. With limit budget and resources, they want to create a new disaster recovery site that utilizes a Ne...

What must you specify when you create a Vserver for block protocols?

Which command do you use on a Brocade FC switch to view all defined zone configuration information?

Which command do you use to view the current running configuration on a Nexus switch?

During a storage failover operation, paths to the down node will show as:

What information is replicated across the SAN replicated database ring in Data ONTAP Cluster- Mode 8.1 and later?

What information do you NOT need to verify before ordering a NetApp storage solution?

When Data ONTAP is running in Cluster-Mode, a portset contains an access list consisting of_________.

What does NetApp recommend as best practice for zone configuration?

Which two must you specify when creating a volume? (Choose two.)

The storage administrator wants to ensure resilient non-interruptive access to a LUN in a cluster even if the volume containing the LUN is moved to any node within the cluster. Wha...

With Brocade FC switches, which commands will show you that the current configuration is supporting NPIV for the ports that are using it? (Choose three.)

NetApp storage systems require which information to configure the storage system for management tools? (Choose two.)

What is the storage system command line interface command fcp adapter show used to determine?

How do you enable an FC port on a Cisco switch?

For a Brocade Fibre Channel switch, which commands can you use to check the devices that have logged in to the switch? (Choose two.)

When running Data ONTAP in Cluster-Mode, which three statements are true about Asymmetric Logical Unit Access (ALUA)? (Choose three.)

iSCSI and FC SAN deployments share requirements for these planning steps with one exception. Which task is NOT required for both types of deployments?

Portsets limit host access to certain paths when they are bound to ____________.

When applied to an igroup, what is the function of a portset?

How many nodes are supported running san protocols in Clustered Data ONTAP 8.2?

Which three does clustered Data ONTAP support for iSCSI with Microsoft Windows 2012solutions? (Choose 3)

What is the name of the Brocade Fibre Channel switch OS?

Where would you go to find out more information about how to configure a Brocade FC Switch?

A storage administrator tested a storage failover but when attempting a giveback, the data aggregate was not returned to the original controller until after boot up of DATA ONTAP....

When running clustered Data ONTAP, which topology allows for guaranteed maximum network performance for iSCSI?

The NetApp storage solution diagram for installation should include which three pieces of information (choose three.)

By default, what is allocation that the NetApp Unified Target Adapter uses between FCoE and other Ethernet traffic?

Which protocol does the FC Frame encapsulate within FCoE?

An FC port on a NetApp storage system running clustered Data ONTAP is connected to an FC switch. FCP is licensed on the cluster and the Vserver FCP service is created and running....

For a Brocade Fibre Channel switch, which command can you use to check whether two devices zoned properly and whether connectivity exists?

Which is NOT a correct igroup configuration?

A node's FC port is performing a Fabric Login however, the N_Port ID is not being virtualized. What is a likely cause?

During a storage failover operation (SFO), a host accessing a LUN via the iSCSI protocol:

A NetApp storage system running clustered Data ONTAP is logged in to an FC switch. An initiator logged in to the same switch. FCP is licensed, and the TCP service is created and ru...

On a Cisco Nexus 5000 series switch, what must occur before the FCoE initiators and FCoEtargets can discover each other?

To ensure correct version and patches for host capabilities such as multipathing and host clustering on specific OSes such as Solaris with Veritas DMP, which tool or information so...

After proper cabling, enabling the FC ports on the initiator and target, and creating a LIF within a Vserver, you still are not able to see the initiator using the Vserver fcp init...

What is the name of the SAN replicated database ring in clustered Data ONTAP 8.2 and later?

When creating a LUN, you use the LUN's OS type to specify which two? (Choose two)

You need to gather information from the host systems that will be attached to the NetApp storage systems using either FC, FCoE or iSCSI. This information includes operating system...

The NetApp Host Utilities Kits provide which two functions? (Choose two)

Spaces has to be available in the Data Center for which storage elements or devices? (Choose three)

In clustered Data ONTAP 8.2, which two statements are true? (Choose two.)

How must licenses lot block protocols be installed? (Choose two.)

How can you "throttle" SnapValue updates and baseline transfers so that the primary or secondary is not transmitting data as it can?

Node 1 in a clustered pair detects that it has lost connectivity to one of its disk shelves. Node 1 is still up, but it cannot see one of its disk shelves. However, the partner nod...

In Data ONTAP, the root user is exempt from those two quotas: ______________. (Choose two)