NS0-171 Exam Questions
112 real NS0-171 exam questions with expert-verified answers and explanations. Page 1 of 3.
- Question #1
Which statement is true for Fibre Channel QoS System Class?
- Question #2
Which pool of addresses is created under Servers tab in UCS Manager as part of the Service Profile creation process?
- Question #3
For a `boot from SAN' configuration, which two features must be enabled? (Choose two)
- Question #4
What aggregate containing the root volume is created during the Clustered Data ONTAP setup process?
- Question #5
NetApp recommends that your SSL key length be?
- Question #6
Refer to the exhibit. When configuring a Cisco UCS B-Series server to support boot from SAN in a FlexPod deployment, which statement is correct?
- Question #7
When installing an instance of VMware ESXi on a UCS B-Series server, where should an ISO image be loaded?
- Question #8
Refer to the exhibit. What management tool may be used for creating virtual machines?
- Question #9
When creating a virtual machine in VMware vSphere 5.x, which type of virtual disk should be provisioned if you would like to fully pre-allocate storage with the highest chance of b...
- Question #10
Which four items are required in order to create a Gold Master Boot LUN to automate the provisioning of Hyper-V hosts using the built-in LUN cloning capabilities of NetApp storage?...
- Question #11
Which two are the expected outputs of network interface show? (Choose two.)
- Question #12
Which sends support summary information to NetApp through HTTPS?
- Question #13
When configuring a volume to contain a LUN, which administrative tool automatically applies NetApp recommendations?
- Question #14
When trying to configure a Virtual Port Channel (vPC), what might be a cause of the following error when trying to create the vPC domain?. Nexus-5548-B(config)# vpc domain 10 ^% In...
- Question #15
Which tool can be used to validate hardware installation in a FlexPod solution?
- Question #16
Which policy detail should be set if you want a server to be exempt from all power capping?
- Question #17
Which two are correct about VSAN configuration within UCS Manager? (Choose two)
- Question #18
Which two are true about Fabric Interconnect L1 and L2 ports in cluster mode? (Choose two)
- Question #19
There are 2 chassis tied to a pair of Fabric Interconnects. First chassis, chassis-1, has 1 link between single IOM and Fabric Module. Second chassis, chassis-4, has 4 links betwee...
- Question #20
With Clustered Data ONTAP, which three protocols are supported for host boot in a UCS stateless computing environment in the FlexPod configuration? (Choose three.)
- Question #21
Which three are types of Storage Virtual Machines? (Choose three.)
- Question #22
Which aggregates should be disabled for data aggregates?
- Question #23
Which three are characteristics of a NAS data LIF? (Choose three.)
- Question #24
Which two are characteristics of a Fibre Channel SAN data LIF? (Choose two.)
- Question #25
Which two LIFs are able to failover or migrate to other nodes in the cluster? (Choose two.)
- Question #26
Which server role is required to support running virtual machines on a Microsoft based hypervisor?
- Question #27
Clustered Data ONTAP 8.1 or later provides what four storage efficiency features? (Choose four.)
- Question #28
What software program manages a NetApp storage controller with Data ONTAP 8.1 or later?
- Question #29
Which endpoint's firmware can be directly upgraded (without the use of a Service Profile) using UCS Manager?
- Question #30
When creating local user, which two are valid user names? (Choose two)
- Question #31
How.many VEMs can one server have?
- Question #32
Your primary VSM needs to be edited, rebooted, or migrated. You need to initiate a manual switchover to your standby VSM. What command will allow this to occur?
- Question #33
To install your VEM, what is the extension of the VEM file name you'll be looking for to complete this install?
- Question #34
How do the Fabric Interconnect ports connecting to the 2232PP FEX have to be configured?
- Question #35
When connecting the Nexus 1110-X to the Nexus switch, what Spanning Tree port type is used?
- Question #36
How should the speed be configured on the Nexus 5548 port connecting to the Nexus 1100-X?
- Question #37
What management solution can provision all three components of a FlexPod (NetApp storage, Cisco UCS compute and Cisco Nexus network)?
- Question #38
How many ACTIVE SPAN sessions exist on a Fabric Interconnect?
- Question #39
Which two are two possible features of the `Call Home' feature in UCS Manager?
- Question #40
Given the following switch output, where would you expect see notification level messages?.N5K- 1# show logging info.Logging console: enabled (Severity: error)Logging monitor: enab...
- Question #41
Which item is an example of Role-Based Access Control and multi-tenancy support that can be applied to a UCS environment using the Cisco UCS Manager?
- Question #42
Which three are true for UCS 2208XP? (Choose three)
- Question #43
Which two are required for single-wire management for Cisco UCS C-Series? (Choose two)
- Question #44
Refer to the exhibit. Which is correct for configuring FCoE?
- Question #45
How are jumbo frames enabled on the Nexus 5548?
- Question #46
Which is a valid connectivity option for a FlexPod? Note some of these may also be 'valid' options outside of a FlexPod architecture but do not specifically meet FlexPod scalabilit...
- Question #47
How many cluster interconnect switch(es) are required for a 4-node NetApp cluster?
- Question #48
To support Storage Virtual Machines, which type of unique login account must be created?
- Question #49
Which statement is true about NFS exports in Clustered Data ONTAP?
- Question #50
When using Clustered Data ONTAP 8.1 and later, what is the default for new aggregates?