NS0-164 Exam Questions
206 real NS0-164 exam questions with expert-verified answers and explanations. Page 3 of 5.
- Question #101
A NearStore system or storage appliance can operate as a secondary and primary system at the same time.
- Question #102
Which one of the following commands is used to specify the destination appliance(s) that are allowed to replicate (pull) data from the source appliance?
- Question #103
Fill in the blank for the following statement: To manage a SnapVault backup through a commercial NDMP application, you must specify a_____authorized through that application.
- Question #104
Which statement is true of the cf forcetakover -d command?
- Question #105
Each storage appliance in a cluster must have network access to the
- Question #106
Which three are required licenses for Fabric Attached MetroCluster? (Choose 3)
- Question #107
Which tool is available on a non-NetApp primary system to assist in starting or stopping SnapVault, modifying NDMP settings, enabling debugging, and capturing trace files?
- Question #108
Which statement describes the results of the snapmirror resync command?
- Question #109
Which one of the following statements is not true of SnapLock volumes?
- Question #110
Which one of the following is a recommended secondary system for SnapVault?
- Question #111
Which MetroCluster configuration procedure is recommended for re-establishing a mirrored volume that was in a level-0 re synchronization state when it failed?
- Question #112
Fill in the blank for the following statement using the best answer from the choices that follow. A snapshot is a frozen, read-only image of the entire Data ONTAP file system that...
- Question #113
Normally, before you split a SyncMirror volume, you ensure that both plexes are
- Question #114
Which one of the following commands or procedures would you use to undo a SnapRestore reversion?
- Question #115
Which one of the following /etc/snapmirror.conf entries will not support synchronous SnapMirror?
- Question #116
Fill in the blank for the following statement: To manage a SnapVault backup through a commercial NDMP application, you must specify a_____authorized through that application.
- Question #117
Alter a SnapRestore reversion of a volume, incremental backup and restore operations on the file or volume cannot rely on the timestamps to determine what data needs to be backed u...
- Question #118
NetApp X1024 Fibre Channel HBA is required on the storage systems for IP over Fibre Channel functionality.
- Question #119
In a synchronous SnapMirror configuration, the source storage appliance exhibits high latency due to user traffic and rapid data change from SnapMirror transactions. Which one of t...
- Question #120
In a Fabric Attached MetroCluster, a "disaster" is described as a:
- Question #121
Which one of the following commands would you use to disable client access to snapshots on a volume called /vol/flexvoM?
- Question #122
What user-controllable security mechanism is built into OSSV?
- Question #123
Which two of the following statements apply to the fs_size_fixed volume option?
- Question #124
Which one of the following statements apply to Advanced Single Instance Storage (ASIS)?
- Question #125
Which one of the following statements does not apply to the SnapMirror visibility-interval variable?
- Question #126
You have quiesced a volume to stabilize the contents of a destination just prior to a snapshot. What is the next logical command that you would issue after the snapshot is complete...
- Question #127
Exhibit: To remove a cluster setup, you must perform the steps displayed in the exhibit.
- Question #128
Which one of the following statements apply to the Free Space Estimator utility?
- Question #129
Which one of the following options will allow a snapmirror storage appliance to mirror from this system?
- Question #130
You can avoid data corruption when you issue the cf forcetakeover-d command if the remote node is
- Question #131
What is the maximum distance between a standard clustered pair?
- Question #132
You want to create an automated test environment that performs a single file SnapRestore. Every time you run the procedure, however, SnapRestore prompts you to confirm your decisio...
- Question #133
In a synchronous SnapMirror configuration, the soui'ce storage appliance exhibits high latency due to user traffic and rapid data change from SnapMirror transactions.Which one of t...
- Question #134
Which one of the following is not recommended asasecondary system forSnapVault?
- Question #135
The Snap Vault secondary system makes a snapshot of its own volume where the qtrees are located.
- Question #136
Which Data ONTAP option would you enable to set system wide throttling for all transfers?
- Question #137
Fill in the blanks for the following statement: The qtree specified for_____must not exist on the secondary system before you run the_____command.
- Question #138
The snapvault restore command is ran on the:
- Question #139
The snapvault snap create volume snapname command can be executed on the__________.
- Question #140
How can you "throttle" Snap Vault updates and baseline transfers so that the primary or secondary is not transmitting data as fast as it can?
- Question #141
Which tool is available on a non-NetApp primary system to assist in starting or stopping Snap Vault, modifying NDMP settings, enabling debugging, and capturing trace files?
- Question #142
SnapVaulr snapshots for SnapLock volumes are deleted automatically according to the retention count set in the SnapVault schedule?
- Question #143
How would you initiate a cluster takeover of filer2 from filer 1?
- Question #144
Which command allows yon to access the other nodes console after a takeover has occurred?
- Question #145
Which two commands could be used if the cf giveback command foils? (Choose 2)
- Question #146
If an error message indicates that the cluster interconnect adapter itself is faulty, what is your corrective action?
- Question #147
To remove a cluster setup, you must perform the following steps. 1. Type cf disable. 2. Unlicense cluster. 3. Remove partner entries for network interfaces from the /etc/rc file. 4...
- Question #148
You are troubleshooting a clustered failover problem at a customer site. The customer explains that both storage appliances were NFS mounted onto the Solaris host. You attempt to c...
- Question #149
One method of configuring an interface for takeover is to enter ifconfig interface partner address at the command line. To make tins configuration persistent across reboots, you mu...
- Question #150
For aggregates or traditional volume SyncMirror to work correctly, the configuration of each plex must be identical with regard to____________.