NS0-163 Exam Questions

A NearStore system or storage appliance can operate as a secondary and primary system at the same time.

Which one of the following commands is used to specify the destination appliance(s) that are allowed to replicate (pull) data from the source appliance?

Fill in the blank for the following statement: To manage a SnapVault backup through a commercial NDMP application, you must specify a_____authorized through that application.

Which statement is true of the cf forcetakover -d command?

Each storage appliance in a cluster must have network access to the

Which three are required licenses for Fabric Attached MetroCluster? (Choose 3)

Which tool is available on a non-NetApp primary system to assist in starting or stopping SnapVault, modifying NDMP settings, enabling debugging, and capturing trace files?

Which statement describes the results of the snapmirror resync command?

Which one of the following statements is not true of SnapLock volumes?

Which one of the following is a recommended secondary system for SnapVault?

Which MetroCluster configuration procedure is recommended for re-establishing a mirrored volume that was in a level-0 re synchronization state when it failed?

Fill in the blank for the following statement using the best answer from the choices that follow. A snapshot is a frozen, read-only image of the entire Data ONTAP file system that...

Normally, before you split a SyncMirror volume, you ensure that both plexes are

Which one of the following commands or procedures would you use to undo a SnapRestore reversion?

Which one of the following /etc/snapmirror.conf entries will not support synchronous SnapMirror?

Fill in the blank for the following statement: To manage a SnapVault backup through a commercial NDMP application, you must specify a_____authorized through that application.

Alter a SnapRestore reversion of a volume, incremental backup and restore operations on the file or volume cannot rely on the timestamps to determine what data needs to be backed u...

NetApp X1024 Fibre Channel HBA is required on the storage systems for IP over Fibre Channel functionality.

In a synchronous SnapMirror configuration, the source storage appliance exhibits high latency due to user traffic and rapid data change from SnapMirror transactions. Which one of t...

In a Fabric Attached MetroCluster, a "disaster" is described as a:

Which one of the following commands would you use to disable client access to snapshots on a volume called /vol/flexvoM?

What user-controllable security mechanism is built into OSSV?

Which two of the following statements apply to the fs_size_fixed volume option?

Which one of the following statements apply to Advanced Single Instance Storage (ASIS)?

Which one of the following statements does not apply to the SnapMirror visibility-interval variable?

You have quiesced a volume to stabilize the contents of a destination just prior to a snapshot. What is the next logical command that you would issue after the snapshot is complete...

Exhibit: To remove a cluster setup, you must perform the steps displayed in the exhibit.

Which one of the following statements apply to the Free Space Estimator utility?

Which one of the following options will allow a snapmirror storage appliance to mirror from this system?

You can avoid data corruption when you issue the cf forcetakeover-d command if the remote node is

What is the maximum distance between a standard clustered pair?

You want to create an automated test environment that performs a single file SnapRestore. Every time you run the procedure, however, SnapRestore prompts you to confirm your decisio...

In a synchronous SnapMirror configuration, the soui'ce storage appliance exhibits high latency due to user traffic and rapid data change from SnapMirror transactions.Which one of t...

Which one of the following is not recommended asasecondary system forSnapVault?

The Snap Vault secondary system makes a snapshot of its own volume where the qtrees are located.

Which Data ONTAP option would you enable to set system wide throttling for all transfers?

Fill in the blanks for the following statement: The qtree specified for_____must not exist on the secondary system before you run the_____command.

The snapvault restore command is ran on the:

The snapvault snap create volume snapname command can be executed on the__________.

How can you "throttle" Snap Vault updates and baseline transfers so that the primary or secondary is not transmitting data as fast as it can?

Which tool is available on a non-NetApp primary system to assist in starting or stopping Snap Vault, modifying NDMP settings, enabling debugging, and capturing trace files?

SnapVaulr snapshots for SnapLock volumes are deleted automatically according to the retention count set in the SnapVault schedule?

How would you initiate a cluster takeover of filer2 from filer 1?

Which command allows yon to access the other nodes console after a takeover has occurred?

Which two commands could be used if the cf giveback command foils? (Choose 2)

If an error message indicates that the cluster interconnect adapter itself is faulty, what is your corrective action?

To remove a cluster setup, you must perform the following steps. 1. Type cf disable. 2. Unlicense cluster. 3. Remove partner entries for network interfaces from the /etc/rc file. 4...

You are troubleshooting a clustered failover problem at a customer site. The customer explains that both storage appliances were NFS mounted onto the Solaris host. You attempt to c...

One method of configuring an interface for takeover is to enter ifconfig interface partner address at the command line. To make tins configuration persistent across reboots, you mu...

For aggregates or traditional volume SyncMirror to work correctly, the configuration of each plex must be identical with regard to____________.