JN0-360 Exam Questions

Which three BGP attributes are used for loop prevention? (Choose three.)

You are attempting to influence return traffic into your autonomous system by preferring one router as an entry point. Which two BGP attributes will affect this behavior? (Choose t...

Which three BGP attributes must be sent to EBGP peers? (Choose three.)

What is a valid BGP neighbor state?

Which statement is true regarding BGP?

A route to the same destination is received from two different BGP sources. Which criterion is considered first to determine the active BGP route?

You are troubleshooting a BGP-learned prefix that is not being installed in the routing table. Which command shows you the missing route?

You are asked to configure a new external BGP connection to a peer's loopback interface. You verify that the peer's loopback interface is reachable, but the BGP connection remains...

Which two statements are true about virtual switches? (Choose two.)

In Q-in-Q tunneling, what is the purpose of the pop-swap operation?

What are three components of the tag portion of an 802.1Q-tagged Ethernet frame? (Choose three.)

Which three mechanisms are used by switches to build and maintain bridge tables? (Choose three.)

What is the purpose of a trunk link?

What are two differences between RSTP and VSTP? (Choose two.)

A rogue switch has been added to your network, exchanged BPDUs, and is now part of the spanning tree topology. Which feature would help prevent this from happening in the future?

What is the maximum number of MSTIs supported in an MST region?

Which two statements are true about STP and RSTP? (Choose two.)

What are two types of BPDUs in the Spanning Tree Protocol? (Choose two.)

You are asked to establish an MPLS LSP between two sites. You are required to ensure the LSP traverses specific routers within your network. Which solution is correct?

Which statement is correct about the inet.3 routing table?

Which two statements are correct about default MPLS behavior on Junos devices? (Choose two.)

Which two statements regarding the MPLS label information base are correct? (Choose two.)

Which two statements are correct about RSVP path messages? (Choose two.)

Which two statements are correct regarding LDP-signaled VPLS instances? (Choose two.)

Which two statements are correct regarding LDP-signaled Layer 2 circuits? (Choose two.)

Which two statements are correct regarding BGP-signaled Layer 2 VPNs? (Choose two.)

Which two statements regarding VRF tables are correct? (Choose two.)

You have been asked to implement routing policy on the PE devices in your AS and to ensure the correct customer routes are installed in the appropriate VRF tables. Which component...

What is the purpose of a route target community in a Layer 3 VPN?

You have been asked to deploy a Layer 2 VPN for a new customer. What information will be present in the PE's associated VPN forwarding table? (Choose three.)

You have an established Layer 3 VPN where you are using static routing between your PE and CE devices. You must advertise their directly connected subnet to remote PE devices. Whic...

You have been asked to verify the state of an LDP-signaled Layer 2 circuit. Which two commands would you use to verify the state of the connection? (Choose two.)

What are two valid IPv6 addresses? (Choose two.)

Which new field is added to the IPv6 header when compared to IPv4?

Which three are valid IPv6 extension headers? (Choose three.)

What are two components of an IPv6 router advertisement message? (Choose two.)

Which two statements are correct about neighbor discovery in IPv6? (Choose two.)

You want to configure an interface on your router to use an IPv6 global IP address. Which three methods accomplish this task? (Choose three.)

Which two support tunneling for non-IP protocols on Junos devices? (Choose two.)

Which two support the tunneling of IP traffic on Junos devices? (Choose two.)

Which two statements are true regarding GRE tunnels? (Choose two.)

Which two statements are true regarding GRE tunnel overhead? (Choose two.)

Click the Exhibit button. You are advertising the route in the exhibit to your OSPF neighbors. What happens if the 10.0.0.0/16 route is unavailable? user@router> show route 0/0 exa...

Click the Exhibit button. You have been asked to configure per-packet load balancing. Referring to the exhibit, which configuration correctly applies the load-balancing policy? [ed...

Referring to the exhibit, what is the result of the RIB group configuration? [edit] user@router# show routing-options rib-groups { test { import-rib [ walter.inet.0 nancy.inet.0 ];...

Referring to the exhibit, which statement is correct? {master}[edit] user@router-RE0# run show task replication Stateful Replication: Enabled RE modE. Master Protocol Synchronizati...

You have been asked to determine if an NSR switchover will be hitless for a given BGP peer. Referring to the exhibit, which statement is true? {master}[edit] user@router-RE0# run s...

Click the Exhibit button. R1 and R2 are using VRRP for high availability. Referring to the exhibit, which two statements are correct about the configuration? (Choose two.) user@R1>...

Click the Exhibit button. The router was just powered on. Referring to the exhibit, what is the OSPF RID? interfaces { ge-1/0/3 { unit 0 { family inet { address 192.168.1.1/30; } }...

Referring to the exhibit, what is the resulting behavior on interface ge-1/0/0? protocols { isis { level 1 disable; interface ge-1/0/0.0 { level 2 disable; } interface ge-1/1/0.0;...