JN0-360 Exam Questions

You are logged into a PE router participating in a Layer 3 VPN as defined in RFC 4364. You would like to ping the locally connected CE router's interface. The address of the interf...

Click the Exhibit button. From the output shown in the exhibit, what would happen to a packet destined for address 172.29.3.5?

Before configuring an RSVP LSP in your network, you first apply a baseline configuration to all of the routers.Which three configuration elements are minimally required in the base...

Your customer complains that their Layer 3 VPN is not passing traffic from one site to another. You assigned that customer to VPN-A. Which command on the PE router will confirm the...

In an IS-IS network, which device represents the pseudo-node?

Router B is an OSPF router connected to both Area 0 and Area 2. Area 2 has been configured as a totally stubby area.Which three LSA types does Router B suppress from Area 2? (Choos...

What is the size of the unique address used to identify each node on an Ethernet LAN?

Which two IS-IS packet types are used to maintain IS-IS database synchronization? (Choose two.)

You notice that a route from internal BGP peer 192.168.1.1 is missing from the local route table.Which two commands would be used to help identify the source of the problem? (Choos...

What are three ways to configure IPv6 addresses in your network? (Choose three.)

Click the Exhibit button. Which two topologies shown in the exhibit could be implemented without a spanning-tree protocol? (Choose two.)

Click the Exhibit button. In the exhibit, all routers are sending routes to Router B.Which routes will be advertised from Router B to Router E?

In your RSVP network you have configured three separate LSPs to the same egress address. You have made no other configuration changes to the forwarding decisions made by the router...

Which two values are used by an RSTP bridge to remove stale BPDU information? (Choose two.)

Click the Exhibit button. After the MAC learning limit of 3000 is reached for the bd bridge domain as shown in the exhibit, what happens to frames that arrive that contain unknown...

You have recently configured MSTP on two switches in your network to participate in the same MSTP region. You issue the show spanning-tree mstp configuration command on both switch...

You have a stub OSPF area running in your network. Your supervisor has asked you to build a virtual link across this area to connect new equipment acquired in a recent ISP acquisit...

You own a small company and need to assign IPv6 addresses to your routers. Because you want to follow the guidelines spelled out in RFC 3177, you want to design your network with t...

Your customer would like to forward traffic using DLCI 600 and maintain Layer 2 information across a VPN.Which solution will meet these requirements?

You have two OSPF routers that are trying to form an adjacency. When you issue the command show ospf neighbor, you see that one router is in the loading state and the other is in t...

Which two events could cause the BGP Active state to appear? (Choose two.)

Click the Exhibit button. The policy shown in the exhibit has been configured and installed on your router. What is the result of applying this policy?

Which type of router can provide connectivity between areas in an IS-IS domain?

You have been asked to provision a service provider's network to accommodate Layer 3 VPNs as defined in RFC 4364.Which three tasks must be performed before the provider network is...

By default, which BGP attribute is only compared when two route advertisements are received from the same neighboring AS?

Click the Exhibit button. Referring to the exhibit, what must be true of the vlan_100 bridge domain?

An Ethernet bridge is configured such that all interfaces are in a single broadcast domain.Which two tasks does the bridge perform in response to receiving a frame with an unknown...

You have configured multiple IP-IP tunnels across your network to provide connectivity to remote sites.Which technique is used to help the IP endpoints in your network determine th...

You are asked to design a Layer 2 VPN service between service provider networks that needs Ethernet transport capabilities. The VPN should support two or three endpoints. Which Lay...

You are adding nonforwarding route reflectors to your network. Which three actions ensure that VPN routes are advertised properly? (Choose three.)

Which two statements describe advantages of using BGP for VPLS signaling instead of LDP signaling? (Choose two.)

Which two statements are true when configuring OSPF authentication? (Choose two.)

Which three statements are true about the BGP community attribute? (Choose three.)

An IS-IS level 1-only router is configured within a larger multilevel hierarchy. Which OSPF area type resembles the routing information in the L1 router's table?

Which statement is true about IS-IS?

What does the Junos command advertise-inactive allow?

An LDP Layer 2 circuit is configured for VPN A and VPN B. Which three statements are true regarding LDP Layer 2 circuit signaling? (Choose three.)

Your are the administrator for a network that uses IS-IS as its IGP. As the network grows, you find that the protocol's default capabilities for setting metrics is limiting your op...

You are monitoring the control plane traffic using a network analyzer on an Ethernet network segment with all routers configured with IS-IS routing. Which two statements are true?...

BGP AS-PATH is :

Protocol Isis { interface lo0.0 interface ge-0/0/0.0 } What is the level of IS-IS router.

Router A has external peer 10.1.20.1 and many internal peers , we have the following policy : Policy-options policy-statement nhs term 1 { from protcol bgp neighbor 10.1.20.1 Then...

show interface on Junos platform. what is true about the two ipv6 address on interface ge0/0/0?

We use rsvp to built three LSP path, one primary LSP and two other backup LSP, which command to show which LSP path has been used to foward traffic.

Which ldp packet use to sending FEC information :

You have configured an RSVP LSP in your network and have assigned it one primary and two secondary paths. Which command is used to validate that the LSP is using the primary path?

What are two uses of the AS-path attribute? (Choose two.)

Which IS-IS packet is used to carry routing updates?

Which three elements contribute to the bridge ID when configuring RSTP? (Choose three.)

Which LDP message is used to transmit labels and forwarding equivalency class (FEC) information?