JN0-101 Exam Questions
213 real JN0-101 exam questions with expert-verified answers and explanations. Page 4 of 5.
- Question #154
In the exhibit, what does the (>) symbol indicate?
- Question #155
Bye default, what are three valid routing tables? (Choose three)
- Question #156
Which statement is true about the forwarding plane?
- Question #157
Which two can be used to create and apply an export policy that advertises static routes to RIP neighbors? (Choose two)
- Question #158
You must segement your internal 192.168.1.0/24 network into a minimun of 12 subnet, each containing a minimun of 12 hosts. Which network mask do you use?
- Question #159
Which directory does the Junos OS use to store syslog information by default?
- Question #162
Referring to the exhibit, which command would you use to add an additional address to the ge-0/0/9 unit 0 interface? Juniper JN0-101 Exam
- Question #163
Which CLI command should be issued to navigate to the [edit protocols ospf] directory?
- Question #164
Which CLI command must be issued to activate configuration changes in the router?
- Question #165
For the access layer of a data center, the Juniper approach includes:
- Question #166
A benefit of the all-in-one approach to Internet access is:
- Question #167
Which two interfaces are considered permanent interfaces on a Juniper Networks router? (Choose two.)
- Question #168
Which Junos command allows for real-time display of interface statistics?
- Question #169
What is the default clocking mode on a serial interface?
- Question #170
After defining an aggregate route for 0/0, you note that the M7i's system board CPU utilization increases. What might account for this?
- Question #171
You issue the command set routing-options autonomous-system loops 3. What does it do?
- Question #172
You have configured RIP between three routers connected in a serial chain, but no RIP routes are being learned. Which policy results in full RIP connectivity for all direct routes?
- Question #173
You were provided a network diagram that told you to number your network from the 191.255.0.0/16 space. OSPF is enabled and adjacencies are up, but no routers are learning any rout...
- Question #174
When export policy is specified at the global, group, and neighbor levels, which policy is executed?
- Question #175
When you issue a show bgp summary command, what is indicated by the Active state?
- Question #176
What is the purpose of the shaping-rate statement in the following code snippet? test_sched { transmit-rate percent 5; shaping-rate percent 20; priority high; }
- Question #177
When committing a CoS configuration, you notice the following log message. What does it mean? Oct 30 05:39:15 Bock cosd[1071]: COSD_TX_QUEUE_RATES_TOO_HIGH: Unable to apply schedul...
- Question #178
Refer to the output provided and select the best answer: lab@Porter> show multicast route Family: INET Group: 225.1.1.1 Source: 10.10.111.1/32 Upstream interface: ge-0/0/1.1331 Dow...
- Question #179
What represents the decimal equivalence of 11100101?
- Question #180
Which login class permission will allow a user to use the telnet utility?
- Question #181
Which statement is true about terms in a policy?
- Question #182
What is the decimal equivalent of 10101010?
- Question #183
Two devices on an Ethernet segment sent frames at the same time causing a collision. Which two statements are true? (Choose two.)
- Question #184
You issue the command telnet interface ge-1/1/0 10.10.10.1 source 192.168.100.1 bypass-routing. Juniper JN0-101 Exam Which statement is correct?
- Question #185
How can you verify that you have correctly configured SSH access to your Junos device?
- Question #186
Which statement describes an advantage of dynamic routing?
- Question #187
Which statement is true about the forwarding plane?
- Question #188
By default, which character indicates the configuration mode prompt?
- Question #189
What is the purpose of a network mask?
- Question #190
Which statement is true about routing tables on a Junos device?
- Question #191
Which statement is true regarding the Junos OS?
- Question #192
A network administrator would like to view detailed interface status, properties, statistics, errors, and CoS packet counters. Which operational command will display this informati...
- Question #193
On which operating system is the Junos OS based?
- Question #194
Which two commands will successfully create ping traffic? (Choose two.)
- Question #195
What are two valid actions for a routing policy? (Choose two.)
- Question #196
You have been asked to configure your MX240 with a default route toward your upstream ISP at IP address 192.168.100.1. Which command successfully completes this task?
- Question #197
The IP address 192.168.100.1 belongs to which class of IP address space?
- Question #198
Which CLI keyboard sequence allows you to move the cursor to the beginning of the line? Juniper JN0-101 Exam
- Question #199
For the interface ge-1/2/3.4, what does the "ge" represent?
- Question #200
You must segment your internal 192.168.1.0/24 network into a minimum of 12 subnets, each containing a minimum of 12 hosts. Which network mask do you use?
- Question #201
Which two protocols use UDP as a transport protocol by default? (Choose two.)
- Question #202
Your network administrator has asked you to view the real-time interface usage on ge-0/0/0. Which command would be used?
- Question #203
What is the default route preference value for EBGP?
- Question #204
What is the decimal equivalent of 00000110?
- Question #205
The authentication order configuration on your M120 includes the settings tacplus and radius (in that order), but does not include the password parameter. You attempt to log in to...