JN0-101 Exam Questions
213 real JN0-101 exam questions with expert-verified answers and explanations. Page 2 of 5.
- Question #51
Which two commands would you use to view OSPF routes? (Choose two)
- Question #52
What are three terminating actions for firewall filters? (Choose three)
- Question #53
Which three statements are true about terms in a policy? (Choose three)
- Question #54
Your network administrator has asked you to view the real-time interface usage on ge-0/0/0, Juniper JN0-101 Exam Which command whould be used?
- Question #55
What are two Junos processes? (Choose two)
- Question #56
Which statement describes an advantage of a dynamic routing?
- Question #57
Referring to the exhibit, you want to block HTTP access to Web-Server from the subnet where Mai-User is located. All other traffic should be permitted. Which firewall filter config...
- Question #58
You have a network containing 120 routers. You must establish and maintain connectivity between the loopback interfaces of all routers. Because of the critical services using the n...
- Question #59
When configuring more than one archival site, which statement is true?
- Question #60
Juniper JN0-101 Exam An administrator is unable to ping any address on the 10.0.19.0/24 subnet. To identify the problem, the administrator uses the command shown in the exhibit. Wh...
- Question #61
Which statement is true regarding the forwarding plane?
- Question #62
Which two commands may be used when configuring an IP address for a Gigabit Ethernet interface? (Choose two)
- Question #63
What information is used by a switch to forward an Ethernet frame to its destination?
- Question #64
Which statement is true regarding the password-recovery process?
- Question #65
Which two statements are correct regarding the default protocol preference values? (Choose two)
- Question #66
Given the configuration shown in the exhibit, what will happen to traffic from source 10.10.10.25 destined to 200.200.200.1? Juniper JN0-101 Exam
- Question #67
Which two statements apply when a user has entered private configuration mode by typing configure private? (Choose two)
- Question #68
Which command is used to display all output at once?
- Question #69
Which two statements are true about terms in a routing policy? (Choose two)
- Question #70
A packet is evaluated against three user-defined terms within a firewall filter and no match is found. What correctly describes the action the firewall filter will take for this pa...
- Question #71
You are configuring new BGP neighbor and want to view the configuration for the interface ge-0/0/0.42 Which command do you use to achieve this result?
- Question #72
You have received a default route through BGP from your ISP and you want to redistribute it into OSPF. Which mehtod will accomplish this?
- Question #73
What are three examples of dynamic IGPs? (Choose three)
- Question #74
By default if equal-cost paths exists for the same destination, which action will the router take?
- Question #75
Referring to the exhibit, which type of classifier is being used in the CoS configuration?
- Question #76
You have been asked to develop an application that uses only connection-oriented protocols. Which two protocols can you use? (Choose two)
- Question #77
You accidentally configured interface so-0/0/0.0 with 1.1.1.1/32 instead of 1.1.1.1/30 Which two solutions could you use to correct this configuration? (Choose two)
- Question #78
When considering the default behavior of Junos plattforms, which statement is true about archiving configurations?
- Question #79
What are three valid match criteria in a firewall filter applied to a Layer 3 interface? (Choose three)
- Question #80
Given the routing entries shown in the exhibit, which next-hop IP address will be used for the destination IP addreess 192.168.1.159 (Assume that only static routes are available f...
- Question #81
Which class-of-service component allows you to define the bandwidth allocated to different traffic types?
- Question #82
Which two statements are true regarding trace options on Junos devices? (Choose two)
- Question #83
What are the usable host on the 96.6.128.0/19 network?
- Question #84
Which command will save the current active configuration as the rescue configuration?
- Question #85
Which three steps are parts of the root password recovery process? (Choose three)
- Question #86
Using the command user@router# load override lastest.conf where in the file system will the lastest.conf be located?
- Question #87
Which user authenticaton method is supported by the Junos OS as the last resort alternative? Juniper JN0-101 Exam
- Question #88
Which command is used to enable access to J-Web using HTTPS?
- Question #89
Which command do you use as a valid way to view the PICs within a router as well as the PICs' serial numbers?
- Question #90
You have been asked to configure your router to send link-related SNMP trap notifications to the network managemetn system (NMS) located at address 172.16.17.1 Which two commands a...
- Question #91
Which two fields are found in an Ethernet frame header? (Choose two)
- Question #92
What must be configured prior to the first commit after factory defaults are loaded?
- Question #93
Which statement is true regarding the Junos OS?
- Question #94
Which two commands allow you to return to a previous verision of software on the device? (Choose two)
- Question #95
What are three physical interface properties? (Choose three)
- Question #96
Juniper JN0-101 Exam Which two statements are correct about Layer 2 broadcast frames? (Choose two)
- Question #97
Your network administrator has asked you to view the real-time interface usage on ge-0/0/0, Which command whould be used?
- Question #98
There are three static routes in the routing table that need to be announced to your OSPF preers. Which method is used to accomplish this?
- Question #99
Which two statements are true of a network mask? (Choose two)
- Question #100
Which statement is true about the forwarding table?