E20-616 Exam Questions

What is the RAID level used in Power Vault devices?

You installed Symmwin on your service laptop. You tried to run the command A7,C to verify the status of the devices, but the Inlines icon is disabled. What needs to done to success...

What is the default folder where SymmWin 5876 is installed?

What is the maximum amount of cache available in a VMAX 20K Engine using only 8GB DIMM?

A director replacement is required on VMAX 20K. The customer asks what the impact will be on the front-end ports of the director being replaced. What should your response be?

You are replacing Symmetrix FRUs. Which tool/ procedure must be followed before carrying out this activity?

A CE is dispatched to replace a Drive. After logging into a Symmetrix VMAX 40K running Enginuity 5876.159.102 Simplified SymmWin is automatically launched. How should the CE procee...

You are installing a new VMAX 20K for a customer. What do you need to know about the License Activation Code (LAC) name to retrieve the license file?

You are replacing VMAX Standby Power Supplies (SPS). Which tool should be used for this activity?

Which FRU replacements are supported by Simplified SymmWin?

Which Enginuity version introduced Simplified Symmwin?

You are preparing to run a health check on a VMAX 10K and log into the Service Processor, but cannot locate the icon for Simplified SymmWin on the desktop. What is the most likely...

Click the exhibit button. A customer has complained about BCVs that cannot be seen by the host. What does the display 8d,,,GDAT command show about the devices displayed?

Which command is used to display the invalids on device 100?

What device is never addressed by a host?

What functions are performed by the XCM cards?

What is the number of fans located on the top of an 8530?

What is the minimum number of drives that are allowed to configure devices in RAID 3+1 protection?

Click the exhibit button. Which letter represents the DMX-1000 Power Supply?

Click the exhibit button. Where are the ECM cards located in the display?

Which Inlines command will display Invoked Hot spares?

You are viewing the rear of a Symmetrix DMX22000/3000 Card Cage. Where will you find ECM1?

Which commands will help verify a defective drive location?

A DMX-2 memory configuration containing four (4) memory boards is to be upgraded to larger size cache boards. The upgrade results in a two (2) memory board configuration. How will...

What is a major difference in director data flow between the Symmetrix 8000 series and a DMX- 2?

What is a difference between a Symmetrix 8830 and a DMX-2?

When will a customer's host be able to access the data on a BCV?

Click the exhibit button. You are viewing the rear of the DMX1000 card cage. Which card is ECM1?

Click the exhibit button. You are viewing the rear of the DMX1000 card cage. Which card is CCM0?

When is the relationship between a data volume and a BCV created?

When looking at the DMX FA Back Adapter, you notice that one of the SFPs is blue. What does this mean?

What does the Interleave Service Policy manage during a read operation?

Which component of a DMX-2 performs Front End, director-to-director communications?

Click the exhibit button. The customer has handed you this service alert error message. What is the error?

A service processor fails to communicate with directors 1 through 8 in the DMX-2 series. Which component can cause this failure?

A customer's AC power fails to a Symmetrix 8430/8530. In this case, which components will the battery subsystem sustain?

A customer wants to change Host Directors to support SRDF. What distinguishes one director type from another within a Symmetrix 8000 series?

A customer wants to set up an FA port for a 10km distance connection. Which optic mode will meet the customer's need?

All the memory slots in a DMX-1000 are occupied. In this case, what is run from the procedure Wizard to perform Memory Replacement?

On a DMX1000P, how many DAs are required?

Which type of Symmetrix volume contains information on the dynamic mirror policy decisions, error logging, event traces, code image storage, and a dedicated lost write area?

How is DPR enabled?

Where on a UNIX system is the file symapi_db.bin created by default?

What should you do to perform an interfamily microcode upgrade from 5670 to 5671?

Click the exhibit button. In this Inline command, what do the contents inside the box on the top line display?

While troubleshooting an issue in Inlines, you run the 99,A command to view errors posted. There's an E10B error posted. What does the E1 and 0B represent?

When running inline commands, the command structure is Utility, P1, P2, P3. What does P1 represent?

Which Symcli command shows Symmetrix config locks 15?

You are using Inlines to troubleshoot a drive failure. In the command "A7,D,1,12", what does the 1 represent?

Which inline command displays the currently loaded Enginuity Packs in a DMX?