DES-1721 Exam Questions

When planning the necessary Bandwidth for Remote Instant Replay what needs to be considered?

Which component of the Dell Storage Manager (DSM) suite's only purpose is to perform disaster recovery if the primary data collector is no longer available?

You are installing a new SC9000. Which procedure should be used to install and configure the system?

An administrator wants to configure an SC Series array to use Virtual Port Mode. What is a requirement to accomplish this task?

What are the possible methods to upgrade the firmware on a Brocade switch?

A customer is running the Dell Storage Manager (DSM) Suite as a software stack on Microsoft Windows. To reduce the Microsoft licensing costs, the customer wants to switch to the DS...

Which operating system runs the Dell Storage Manager (DSM) as a virtual appliance?

Which best practices should be followed when using iSCSI to connect SC Series arrays and hosts for switches that incorrectly negotiate speed and duplex?

Assume a storage administrator is using the recommended storage profile. What describes the distribution of volume data residing in an SC series storage array that has 15K and 7K a...

A customer is facing poor performance on all synchronously replicated volumes every Thursday between 4 PM and 6 PM. All departments have checked their applications for any batch jo...

A customer is concerned they are over utilizing their 7K drives. Where can information about the real time I/O usage of individual drives be viewed?

A company is using an SC4020 array and the storage administrator wants to expand the available capacity by adding 92, 3.5" disk drives. Which expansion enclosure(s) can be used to...

You have implemented two SC Series systems at a customer site. The Dell Storage Manager (DSM) Suite has been installed on a Microsoft Windows server. Both Storage Centers have been...

Which option will enable compression on an SC Series array volume?

For what is Application Protection Manager used?

When a SC is in a failover state what will occur in the surviving controller?

A customer has a volume that was created with the wrong datapage size. What is the simplest and least disruptive method to change this volume's page size?

What information is required to configure an iSCSI initiator?

What is the maximum number of disks that can be supported by an SC4020 running SCOS 6.6.4 or later?

You need to set up the iDRAC IP address on an SC Series controller with the following details: - IP address 192.168.0.160 - subnet mask 255.255.255.0 - gateway 192.168.0.1 Which co...

Which zones accurately describe the zoning requirement for replication connectivity to be established when the source array is in Legacy Port Mode and the target array is in Virtua...

A customer wants to add an iSCSI path to a Microsoft Windows Server 2012 R1. The server has an existing Fibre Channel path to an SC7020 array for load balancing and high availabili...

Which 64-bit server operating systems are compatible with the Dell Storage Manager (DSM) Client?

Which method can be used to identify the server HBA WWN?

Based on the exhibit, a customer is using Virtual Port Mode. If the primary path for the controller on the "left" is disconnected while running an IOmeter test for a volume owned b...

Based on documented best practices, which options may need to be modified on a server QLogic HBA?

A customer wants to configure a threshold alert definition. Which types of definitions can be configured?

What is the maximum memory supported on a single SC9000 controller?

Why would the Key Management Server (KMS) Settings page appear during installation?

To achieve redundancy, how many connections from the same SC Series controller are required per fault domain?

You are implementing a front-end connection in Legacy Port Mode on an SC4020 in a SAN with two iSCSI switches. What is the minimum number of port(s), per switch, that can be used b...

Which command is used to set the eth0 IP address on an SC4020 controller?

A customer is using an SC8000 array with three chained SC220 expansion enclosures on a single card. They need to expand its capacity by adding an SC280 enclosure. How should the ne...

You are deploying a new SCv2020 system with four additional SCv100 expansion enclosures. What is the spare-to-managed drive ratio?

How many SC420 enclosures can be supported by the SC7020 controller?