DEA-5TT2 Exam Questions

Which flags are used in the TCP header to initiate and end TCP connections or sessions?

A VLAN has been configured to have an IPv6 address and a stateless address autoconfiguration for clients. Which IPv6 address prefix will the default gateway have on a client?

Which fields are mandatory TLVs in a LLDP PDU frame?

Which IEEE standard defines the Data Link Layer, Discovery protocol?

What is the bandwidth of an RPM for a C9010 Network Director?

What is the default route preference value for a Border Gateway Protocol (BGP) internal route?

Which Dell EMC Networking M-Series 10 GbE switch model supports a VLT?

A network administrator has a Dell EMC switch that has been configured with several VLANs. Each VLAN switch virtual interface (SVI) has an IP address assigned to it with each of th...

Which message is sent by a router when TTL expires?

Which formula is used for calculating OSPF interface costs?

What is the Organizationally Unique Identifier (OUI) in the MAC address 00:C4:4F:23:AF:4A?

Which Ethernet frame forwarding method works best when the outbound ports run at the same speed as the inbound port?

Router A is directly connected to Router B over an Ethernet link. The local interface address for the Router A Fo0/48 interface is 144.254.32.2/24. Which routing table entry is vis...

In IPv4, what is the proper conversion from binary to decimal for the number 11010010?

Which Border Gateway Protocol (BGP) version supports IPv6?

What accurately describes IPv6 addressing?

An Ethernet switch receives a frame from a directly connected host. The source MAC address of the frame is not present in the MAC address table for the switch. However, the destina...

What accurately describes OSPF?

What accurately describes the Network Time Protocol (NTP)?

In which Spanning Tree protocol state does a port record MAC addresses but does not forward the data?

Which route type is added to the routing table by a routing protocol?

Which IP address is in the Class B range?

What accurately describes the comparison between stacking and VLT?

On which OSI layers do standard ACL filters operate?

A network administrator has a stack of four Dell EMC Networking S4800 Series switches. Each stack unit is configured with a different priority. Which switch will be elected as the...

Which port type does a Dell EMC Networking N-Series switch have for its console connection?

What is a fundamental risk of the Peer-to-Peer network model?

Which network device functions only at Layer 1 of the OSI model?

What are Network Address Translation (NAT) inside global addresses?

Which topology is considered a best practice when stacking switches?

Which option is used to configure Network Address Translation (NAT) to provide one-to-one mapping between local and global addresses?

What is the valid range assigned to a client during a TCP connection?

Which port and protocol is used by NTP to communicate?

At which layer of the OSI model is the Rapid Spanning Tree protocol used to prevent switching loops?

Which field of the 802.3 frame is used by network interface cards to synchronize their receivers?

Which type of domains are connected by a Layer 2 switch?

Which IEEE 802.3 sublayer provides addressing and mechanisms that enable network devices to communicate, and provides node-to-node flow control and error management?

Which address is a valid 802.3 MAC address?

A network administrator needs to identify which MAC addresses are static. Under which column in the output of the show mac-address-table command is this information displayed?

Which Layer 1 device can be used to enlarge the area covered by a single LAN segment?

What accurately describes the Simple Network Time Protocol (SNTP)?

Which criteria is used to define an extended MAC ACL filter?

Which IPv4 address is in the same network as the IP address 182.15.24.40/23 and assignable to a host device?

Which BASE-T Ethernet standard specifies a CAT6 cable type?

A network administrator created three VLANs on an Ethernet switch. How many broadcast domains are created by the switch?

What are the Protocol Data Units (PDUs) called at the Transport layer?

Refer to the exhibit. Switch A and Switch B are connected to each other. Both switches use interfaces Gi1/0/1 and Gi1/0/2. Switch A has a Spanning Tree priority of 8192 and Switch...

Which nanometer range will an SFP work in multi-mode?

A service technician is deploying four Dell EMC Networking N-Series switches in a company's network. The technician has enabled the Spanning Tree protocol on the switches. Which sw...

A network administrator is troubleshooting an OSPF routing issue. There are two paths to a destination network from one switch. In addition, one path is comprised of four 1 Gb link...