ASVAB Exam Questions
874 real ASVAB exam questions with expert-verified answers and explanations. Page 5 of 18.
- Question #203
Which of the following is a hardwood?
- Question #204
Which of the following is a softwood?
- Question #205
To prevent rapid drying, freshly cut logs are often
- Question #206
A bumping hammer is used to smooth out dents by a(n)
- Question #207
A groover is used to
- Question #208
Sheet metal is formed into round cylinders by using a
- Question #209
The tip of a soldering iron is coated with solder before it is used. This process of coating the tip is called
- Question #210
Punches are used in sheet metal work to
- Question #211
A gauge shows the complete loss of oil pressure while driving. The best action is to:
- Question #212
A two-cycle engine will normally be found on:
- Question #213
The difference between a single-acting and an opposed piston engine is:
- Question #214
A car equipped with limited-slip differential:
- Question #215
Pouring cold water on an overheated engine:
- Question #216
Soft brake-pedal movement can be caused by:
- Question #217
The safest way to make a hole in sheet metal is to:
- Question #218
Rebar is used to:
- Question #219
Nail sets are used to:
- Question #220
In which automotive system would you find a "wishbone"?
- Question #221
If the electrolyte solution in a battery is too low, you should add:
- Question #222
What area of your car should be flushed periodically to maintain optimum performance?
- Question #223
In a hydraulic brake system, if brake action is soft, a likely explanation is:
- Question #224
Car restorers often seek NOS parts. What does NOS stand for?
- Question #225
Schrader valves can be found in your car's:
- Question #226
A bent frame causes:
- Question #227
When finishing a piece of wood, it's best to sand:
- Question #228
To measure an angle other than a 90-degree angle, the best tool to use is a:
- Question #229
The above tool is a(n):
- Question #230
The above tool is used to:
- Question #231
Which is considered the left side of an engine?
- Question #232
The letter and numbers G78-15 printed on a tire refer to
- Question #233
"Tracking," in terms of front-end alignment, means that
- Question #234
A car with worn-out shock absorbers
- Question #235
In a three-speed transmission, the cluster gear is supported by the
- Question #236
A clutch release bearing
- Question #237
The general procedure to follow when adjusting a band on an automatic transmission is to
- Question #238
Which of the following screw heads requires a Phillips screwdriver?
- Question #239
The flywheel is attached to the
- Question #240
Overheating the engine can cause all of the following problems EXCEPT:
- Question #241
If an alternator overcharges the battery, a likely explanation is:
- Question #242
The primary purpose of piston rings is to:
- Question #243
Connecting rods connect the piston to the:
- Question #244
In an overhead valve system (OHV), what mechanism opens and closes the valves?
- Question #245
If a car's ignition system, lights, and radio don't work, the part that's probably malfunctioned is the:
- Question #246
If a car uses too much oil, which of the following parts may be worn?
- Question #247
On which automotive system would a "stall test" be performed?
- Question #248
In the tire designation 205/55 R 15 92 H, what does the "H" signify?
- Question #249
A sheet of aluminum should be cut with:
- Question #250
Hammer faces are commonly made of each of the following materials EXCEPT:
- Question #251
Hammers, mallets, and sledges are all striking tools, but mallets and sledges don't have:
- Question #253
The best chisel to use when making a circular cut in metal is a: