199-01 Exam Questions

WCCP uses bits to create and distribute buckets.Using HASH assignment, what are the maximum number of bits used?

WCCP uses bits to create and distribute buckets.Using MASK assignment, what is the maximum number of bits used?

What is the priority bit order for WCCP MASK?

A customer wants to mark the IP precedence value for a passive FTP data connection as flash (flash = CS3).Which of the following are true? (Hint: Use the calculator)

You choose to deploy a Steelhead appliance logically in-path using policy-based routing (PBR) as the traffic redirection method.Additionally, you want to mark the Type of Service (...

What is the primary purpose of Connection Forwarding in WCCP deployments with multiple Steelhead appliances in a single cluster? (Select 2)

Assuming auto-discovery is used, WCCP redirect-in statements would normally be placed on which router interfaces? (Select 2)

When deploying policy-based routing for multiple Steelhead appliances in a cluster, the router should be configured to: (Select 2)

When bi-directional network address translation (NAT) is used between the Steelhead appliances, optimization is not working.A workaround to this is: (Select 2)

Simplified routing learns to associate MAC addresses to IP addresses by: (Select 2)

When would Simplified Routing Destination Only be used? (Select 2)

When enabling MS-SQL Layer 7 optimizations, what are the best practices to use? (Select 2)

What is the default Connection Forwarding keep alive interval?

When Connection Forwarding is in use, when a neighbor fails, the default behavior of the remaining neighbor will be to:

In an implementation using a 4-port card, which interface could be used as the Connection Forwarding neighbor? (Select 2)

In configuring failover settings, which of the following ports is set as the default for communicating with the backup Steelhead appliance?

In configuring failover settings, which of the following interfaces is used for communicating with the backup Steelhead appliance?

Which of the following interfaces should be used for datastore synchronization? (Select 2)

What is the supported redirection scheme/s used when a Steelhead appliance is in a WCCP deployment?

When enabling WCCP v2 support, what does a multicast TTL value of 1 imply?

Which of the following control messages are NOT used by WCCP? (Select 2)

Which of the following points on WCCP v2 are correct? (Select 4)

Refer to the exhibit. Assume that a packet being optimized by SH10 incorrectly ends up on SH11 (due to load balancing error, or similar).How can you ensure that this packet is corr...

How can you enable SkipWare?

In the exhibit, where should the WCCP redirection take place for traffic originating from the clients to the servers, assuming redirect IN is used?

Select the command needed to add support for virtual in-path to your Steelhead appliance so that you can use WCCP or PBR with a Steelhead appliance.

In the exhibit, where should the WCCP redirection take place for server return traffic, assuming redirect IN is used? (Select 2)

To prevent possible denial of service attack, such as TCP SYN flooding, which of the following features could be used?

In the exhibit, which interfaces should the WCCP router R1 listen to for multicast communication with the server-side Steelhead appliances, assuming the multicast address is 239.0....

When two or more Steelhead appliances are configured with Connection Forwarding in such environments as WCCP clustering, what feature will allow remaining Steelhead appliances to c...

Refer to the exhibit. The customer would like to prevent a "black-holing" situation when using PBR when SH11 goes down.The Steelhead appliances are directly connected to the router...

Hybrid Mode can best be defined as a combination of:

A customer wants to optimize traffic from remote VPN sites to DMZ servers in the data center shown in the accompanying exhibit. The customer would also like to deploy their data ce...

The Primary interface is REQUIRED for which deployment methods and features? 1) In-path 2) Server-side out-of-path 3) Logical in-path (WCCP/PBR) 4) Hybrid Mode 5) Proxy File Servic...

Which of the following IP addressable interfaces can be connected for management purposes? 1) WAN 2) LAN 3) Primary 4) AUX 5) In-path

The IP address for which neighbor interface should be configured for Connection Forwarding? 1) lan0_0 2) inpath0_0 3) Primary 4) AUX 5) inpath7_7

Refer to the exhibit. In order to achieve optimization using auto-discovery for traffic coming from site C and destined to site A in the exhibit, which configuration below would be...

Which of the following methods can be used to reduce the load on a router configured to use outbound interface WCCP redirection? (Select 3)

Which of the following statements are true about server-side out-of-path deployments? (Select 4)

A server-side logical in-path deployment is shown in the exhibit.Additionally, SH12 is configured with a fixed-target rule pointing to SH11.The client behind SH12 will not be able...

In a WCCP configuration, during a packet trace, you notice the return WCCP communication on a CAT 6500 is using GRE.The Steelhead appliance is directly connected to it.What can be...

What CLI command is used to view logs?

In a previously optimized environment, users have recently upgraded their Windows XP workstations to Windows 7. After the upgrade, users are complaining about slow CIFS and encrypt...

What is the command to view configuration files on the CLI?

Which of the following authentication methods are supported by the Steelhead appliance?

What is the default authorization policy used by Steelhead appliances?

What port number is configured on a Steelhead appliance to communicate to theTACACS+ server?

Which of the following custom TACACS+ attribute-value (AV) pairs gives the user administrative privileges?

Which of the following custom TACACS+ attribute-value (AV) pairs gives the user guest privileges?

What is the default trap severity for system messages?