170-010 Exam Questions

Which two show commands will confirm that a device is receiving OSPF external routes? (Choose two.)

Which command disables hello packets on an OSPF interface?

Which command line will configure the OSPF router ID?

When configuring single-area OSPF, which area number should you use?

Which term describes a single port on an Ethernet switch?

You want to capture all traffic traversing an Ethernet switch on your workstation for protocol monitoring. What must you do?

Which three configuration parameters are auto-detected on a vRouter Ethernet port? (Choose three.)

VLAN 10 is configured on ethernet 0. Which command line will display operational statistics for the VLAN?

Which term is a definition of a VLAN?

VLAN-tagged frames are visible on which ports on a switch?

Which two statements regarding Ethernet link aggregation are true? (Choose two.)

You want to configure a backup static route for a route learned through OSPF. What is the lowest value you can use for administrative distance for this to work?

If all interfaces are active, which route would be preferred?

Which operation allows a firewall to understand complex protocols and pass related traffic automatically?

You've configured a destination port in your firewall rule. Which two additional elements are required in the rule? (Choose two.)

Which two elements are required in a firewall rule? (Choose two.)

Which command displays the headers of packets matching firewall rules?

Which three commands can display rule details, such as protocols and ports? (Choose three.)

Which three commands display whether a firewall rule has been matched by traffic? (Choose three.)

Which three commands should be used to modify a firewall rulebase? (Choose three.)

vyatta@training:~$ show system commit 0 2013-05-03 21:07:54 by root via boot-config-loader 1 2013-05-03 00:05:32 by vyatta via cli 2 2013-05-02 23:15:23 by vyatta via cli 3 2013-04...

Which two elements are required in a source NAT rule? (Choose two.)

Your device receives a mail packet from host 10.1.1.1 to 1.2.3.4 on port eth0. Which rule will the packet match?

Your device is about to transmit a mail packet from host 172.24.42.99 to destination 2.3.4.5 on eth0. Which rule will the packet match?

You have configured a destination port in your NAT rule. Which two additional elements are required in the rule? (Choose two.)

Which statement about NAT is true?

Which two show commands will verify that a Brocade Vyatta vRouter upgrade completed successfully? (Choose two.)

When verifying a new Brocade Vyatta vRouter installation on a hypervisor, which action must be taken with the configuration file?

You are running a Brocade Vyatta vRouter as a virtual machine, and the upgrade system image command tells you that you must perform a manual upgrade. Which three steps are part of...

Which two elements must be configured on your Brocade Vyatta vRouter to use the upgrade system image command? (Choose two.)

Which two elements must you configure in your Brocade Vyatta vRouter to register your software license? (Choose two.)

vyatta@vyatta:~$ show system image The system currently has the following image(s) installed: 1: VSE6.5R3 (default boot) (running image) 2: VSE6.4-2012.08.04 3: VSE6.4-2012.04.30 4...

vyatta@training:~$ show system commit 0 2013-05-03 21:07:54 by root via boot-config-loader 1 2013-05-03 00:05:32 by vyatta via cli 2 2013-05-02 23:15:23 by vyatta via cli 3 2013-04...

vyatta@VYA1:~$ show ip ospf neighbor OSPF process 0: Neighbor ID Pri State Dead Time Address Interface 192.168.131.2 1 Full/Backup 00:00:38 192.168.12.2 eth2 192.168.163.3 1 Init/D...

Based on the output, vyatta@VYA1:~$ show ip ospf database OSPF Router with ID (172.24.42.51) (Process ID 0) Router Link States (Area 0.0.0.0) Link ID ADV Router Age Seq# CkSum Link...

vyatta@VYA1:~$ show ip route ospf O 192.168.12.0/24 [110/1] is directly connected, eth2, 00:07:36 O 192.168.13.0/24 [110/1] is directly connected, eth3, 00:07:36 O *> 192.168.23.0/...

vyatta@VYA1:~$ show ip route Codes: K - kernel, C - connected, S - static, R - RIP, B - BGP O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external t...

vyatta@VYA1:~$ show ip route ospf O 192.168.12.0/24 [110/1] is directly connected, eth2, 00:07:36 O 192.168.13.0/24 [110/1] is directly connected, eth3, 00:07:36 O *> 192.168.23.0/...

vyatta@VYA1# show int eth eth0 address 172.16.32.99/24 duplex auto hw-id 00:0c:29:bf:5c:1b smp_affinity auto speed auto [edit] vyatta@VYA1# Which two commands will activate OSPF on...

vyatta@vyatta:~$ show interfaces Codes: S - State, L - Link, u - Up, D - Down, A - Admin Down Interface IP Address S/L Description --------- ---------- --- ----------- eth0 172.24....

vyatta@vyatta:~$ show interfaces Codes: S - State, L - Link, u - Up, D - Down, A - Admin Down Interface IP Address S/L Description --------- ---------- --- ----------- eth0 172.24....

vyatta@vyatta:~$ show interfaces Codes: S - State, L - Link, u - Up, D - Down, A - Admin Down Interface IP Address S/L Description --------- ---------- --- ----------- eth0 172.24....

Data is being transmitted from host A to host B. If you were to view a frame at the point indicated in the exhibit, what would the source MAC address be?

Data is being transmitted from host A to host B. If you were to capture a frame at the point indicated in the exhibit, what would the source MAC address be?

Data is being transmitted from host A to host B. If you were to view a frame at the point indicated in the exhibit, what would the destination IP address be?

vyatta@vyatta:~$ show dhcp server leases IP address Hardware Address Lease expiration Pool Client Name ---------- ---------------- ---------------- ---- ----------- 10.224.7.40 00:...

vyatta@vyatta:~$ show dhcp server leases IP address Hardware Address Lease expiration Pool Client Name ---------- ---------------- ---------------- ---- ----------- 10.224.7.40 00:...

Your eth1 interface is connected to an ISP, but your user traffic is still not reaching the Internet. You suspect a problem with the DHCP lease. vyatta@vyatta:~$ show dhcp client l...

vyatta@vyatta:~$ show dhcp client leases interface : eth1 last update : Wed Jun 19 00:06:00 GMT 2013 reason : FAIL vyatta@vyatta:~$ Based on the output shown, which two statements...

vyatta@vyatta:~$ show interfaces Codes: S - State, L - Link, u - Up, D - Down, A - Admin Down Interface IP Address S/L Description --------- ---------- --- ----------- eth0 172.24....